ECOMAX 1200

ECOMAX1200 We are proud to introduce our flagship eco friendly energy efficient systems: eco [electrical current optimizer] The eco is an industrial quality electrical current optimizer, designed to lower energy consumption by regulating the use of variable inductive loads in both residential and commercial properties. Reduces the total KWH used while consistently, continuing to supply the proper voltage demands to each specific electrical device's requirements.

Benefits: · Power Factor Optimization (ecowise) · Reduces Energy Consumption By 10% - 30% Per Month (economic) · Provides Power Surge Protection For The Entire Home/Or Business (ecowise) · Increases Motor, Appliances, And Sensitive Electronics Life (economic) · Reduces Noise In The Electrical System (ecowise) · Regulates Voltage (economic) · Improves Quality Of Electrical Current (economic) · Lowers Electrical Magnetic Field Pollution (ecofriendly) · Helps The Environment (ecofriendly) · Made In The USA (ecowise)

LOCATIONS AND INFORMATION:

1. Prior to opening the meter base, or breaker panel, MAKE CERTAIN THE MAIN BREAKER IS IN THE “OFF” POSITION.

2. If there is no space at the meter base, or you prefer, the eM1200 can be installed at the load center (breaker panel).

3. Many homes have multiple breaker panels and the eM1200 can be installed on any breaker panel in the home, providing there is space for the dedicated breaker.

4. The eM1200 is designed to condition “ALL” power consumed by inductive loads (electric motors) in the home regardless of installation location.

5. If there are no spaces available at the meter base or breaker panel, a sub panel can be installed for a dedicated breaker.

6. The eM1200 “MUST” be installed on a dedicated two pole 20 or 30 amp 220 volt breaker or as specified by engineering. Piggy backing is against national building codes.

7. The eM1200 units are enclosed in a NEMA 3R box allowing it to be installed indoors or outdoors, but “CAN NOT” be installed under water.

INSTALLATION INSTRUCTIONS:

1. Prior to opening the meter base or breaker panel MAKE CERTAIN THE MAIN BREAKER IS IN THE “OFF” POSTION.

2. The power should remain “OFF” until the entire installation is complete.

3. Install a two pole 20 or 30 amp 220 volt breaker and secure the Black (L1) and Red (L2) leads of the eM1200 , one on each side of the breaker. Secure the green (GND) wire from the eM1200 to the ground bar in the panel. Leave breaker in “OFF” position until power is restored to panel.

4. Remove “tabs” (knockouts) from the cover allowing access to the breaker after cover is reinstalled. Reinstall the panel cover securely.

5. Turn power (main breaker) back on. Flip the “dedicated” breaker to “ON” and check that the indicator light is on. This will indicate that the unit is on and installation is complete.

6. If the light is “not” on turn off power, and check to make certain good contacts are made with the Black (L1) and Red (L2) wires and the breaker, and the green (GND) wire and the ground bar. Install cover, turn power back on, and check light again.

7. If light remains off call your dealer.

8. If your unit is humming this is a sign that you are receiving high voltage. This will not damage the unit and can occur at various times of the day.

GENERATOR APPLICATIONS:

1. The eM1200 is not designed to improve the power provided by your Generator.

2. If you have a manual start generator, turn off the eM1200 breaker when turning off the main feed breaker.

3. If you have an auto start generator make certain that the eM1200 breaker is not on one of the circuits supported by the generator. If it is turn the breaker off to the eM1200 when the generator starts up.

WARNING: HAVE YOUR eM1200 INSTALLED BY A LICENSED ELECTRICAIN. INSTALLING ELECTRICAL EQUIPMENT MAY RESULT IN SHOCK, SERIOUS INJURY, OR EVEN DEATH.